Date: Sun, 25 Apr 1999 09:25:48 +0000
From: Rafael Bello <bello@stuttgart.netsurf.de>
Subject: COZY: head rests

Do the head rests (chapter 8, page 1) have to be laminated inside and
outside or just outside? I have not found the indication wether in the
plans nor in the email list. What is your opinion?

Regards,
 Rafael Bello

From: cdenk@ix.netcom.com
Date: Sun, 25 Apr 1999 07:47:33 -0500 (CDT)
Subject: Re: COZY: head rests

On 04/25/99 09:25:48 you wrote:
>
>Do the head rests (chapter 8, page 1) have to be laminated inside and
>outside or just outside? I have not found the indication wether in the
>plans nor in the email list. What is your opinion?
>

The Classic is a little different, with the front hinged Canopy, but I glassed the inside of both, made a vertical slot hole 
on the inner faces where I store a Flight Guide, spare handheld mic, sic sacs, and an Airchart's Captains Guide. Plus the ELT 
antenna projects from behind the front seat into the pilots headrest.

Date: Sun, 25 Apr 1999 11:12:40 -0400
From: "Marc J. Zeitlin" <marcz@ultranet.com>
Subject: Fwd: COZY: head rests

Rafael Bello asks;
>
>Do the head rests (chapter 8, page 1) have to be laminated inside and
>outside or just outside? I have not found the indication wether in the
>plans nor in the email list. What is your opinion?

My opinion doesn't matter.  Chapter 8, Step 1, paragraph one says to glass
the inside surfaces with 1 BID, then assemble the headrests.  I suppose it
could be clearer that this one BID is on the inside surface, and not the
outside, but if it were the outside then the later steps of carving the
headrest to shape would be a LOT harder (especially since Figure 8 shows
the outside being glassed with 2 BID).

--
Marc J. Zeitlin           mailto:marcz@ultranet.com
                          http://www.ultranet.com/~marcz/

From: "terren" <guy.terren@wanadoo.fr>
Subject: Re: COZY: head rests
Date: Sun, 25 Apr 1999 18:21:28 +0200

Take care with the head rests.
The height indicated is not exactly the good one.
Compare with TB-1 chapter 18. There is about 3/4" of difference. If you
build them as chapter 8,1 You'll need to cut them. For Mark IV only
...........perhaps

Nat agrees with this.

Regards

Guy

-----Message d'origine-----
De : Rafael Bello <bello@stuttgart.netsurf.de>
 : cozy_builders@canard.com <cozy_builders@canard.com>
Date : dimanche 25 avril 1999 09:49
Objet : COZY: head rests


>Do the head rests (chapter 8, page 1) have to be laminated inside and
>outside or just outside? I have not found the indication wether in the
>plans nor in the email list. What is your opinion?
>
>Regards,
> Rafael Bello
>
>

From: "Nat Puffer" <cozy@extremezone.com>
Subject: Re: COZY: Chap 8 - Belts and Harnesses
Date: Fri, 25 Jun 1999 10:52:09 -0500

Russ,
I have the standard Wicks kit, and over the last 11 years carried all kinds
of shapes, and never had any problem with the fit (they are adjustable).
Regards,
Nat

----------
> From: Russ Fisher <rfisher1@rochester.rr.com>
> To: cozy_builders@canard.com
> Subject: COZY: Chap 8 - Belts and Harnesses
> Date: Friday, June 25, 1999 11:31 AM
> 
> Hi group,
> 
> The standard Wicks kit for Chapter 8 contains the seat belts and shoulder
> harnesses.  Are these required to check for fit during the building
process
> or do they just sit on the shelf until the final assembly?  If so, I
would
> rather put the $370 toward components I can use immediately.
> 
> Thanks,
> 
> Russ Fisher
> 
> 

Date: Fri, 25 Jun 1999 12:11:45 -0500 (CDT)
From: Tom Brusehaver <tgb@wamnet.com>
Subject: Re: COZY: Chap 8 - Belts and Harnesses


>The standard Wicks kit for Chapter 8 contains the seat belts and shoulder
>harnesses.  Are these required to check for fit during the building process
>or do they just sit on the shelf until the final assembly?  If so, I would
>rather put the $370 toward components I can use immediately.

I took one set out to check for fit, and put it in another bag.  I
don't think you need them, you could probably put off getting them. 


How about oshkosh this year, is there gonna be a cozy banquet?

From: Don Bowen <DonBow@symix.com>
Subject: COZY: RE:  Chap 8 - Belts and Harnesses
Date: Fri, 25 Jun 1999 10:31:17 -0700

Russ Fisher wrote:

The standard Wicks kit for Chapter 8 contains the seat belts and
shoulder
harnesses.  Are these required to check for fit during the building
process
or do they just sit on the shelf until the final assembly?  

Here is my two cents worth:

I ordered the chapter 8 kit without the seat belts and shoulder
harnesses.

I just couldn't see paying for these relatively "high dollar" items that
would be left in the box for several years while I build the rest of the
airplane.

I looked at Nat's Cozy Mk IV at the Copperstate Fly-In, and from all
appearances, the seat belts will just bolt right on to the standard
plans built brackets.

I built up the seat belt attach brackets per plans and expect that all
will be well when I go to bolt on the seat belts.

Of course, these are individually built planes and your results may
vary.

Perhaps we will hear from others on this subject.

Good luck with your project.

Don Bowen
Cozy Mk IV, s/n 440 chapter 14






From: "John Slade" <rjslade@bellsouth.net>
Subject: Re: COZY: Chap 8 - Belts and Harnesses
Date: Fri, 25 Jun 1999 13:36:40 -0400

Hi Russ,
I bought one harness to check fit. Was handy but could have done without it.
John Slade
http://kgarden.com/cozy
>
>The standard Wicks kit for Chapter 8 contains the seat belts and shoulder
>harnesses.  Are these required to check for fit during the building process
>or do they just sit on the shelf until the final assembly?  If so, I would
>rather put the $370 toward components I can use immediately.
>
>Thanks,
>
>Russ Fisher
>
>
>

From: cdenk@ix.netcom.com
Date: Wed, 29 Sep 1999 22:46:34 -0500 (CDT)
Subject: Re: COZY:

Was asked: had installed inertia reels onto your front harnesses. 

The inertia reels are aircraft from Wilco (I think, if asked I'll dig out more info). They mount with one bolt 3/8" or 7/16" 
and had black webbing. I made a spreader bar for across the back of the neck, then shipped to Hooker  Harness who sewed the 
reel web and shoulder straps to the bar. The lap belts are standard Cozy. The reels are mounted inside the head rests and on 
top the centersection spar. The hard points are similar to the usual shoulder harness points, which I also installed. I 
believe that with the added reinforcement plus being contained by the headrest structure have sufficient strength, but I have 
no proof of that. I believe that sometimes a yielding structure is better than a very rigid structure, where at some point 
something other than the human body gives, but then there may be another object causing other issues. The reels allow free 
movement, but do lockup on quick movement. When in moderate to severe turbulence, the lap belt tightness is most important, 
and have not noticed the reels locking or not locking. Have several times when lap belts not tight had top of cranium hit the 
plexiglass, but if the lap belts are tight, no contact.

From: "Nat Puffer" <cozy@extremezone.com>
Subject: Re: COZY: headrests
Date: Sat, 2 Oct 1999 18:58:24 -0500

Doug,
That is what we did on our prototype, but then when we stored our headsets
in the strakes, the wires were always in the way of our seats and shoulder
harness. So on the plans model, I put the outlets in the armrests, behind
our elbows. Now we store the headsets in the strakes, and stuff the extra
wires in the pockets, and it doesn't get in the way when we climb in or
out.
It works very well for us. We hope this helps you with your decision.
Nat

----------
> From: DougSheph <dougsheph@home.com>
> To: cozy_builders@canard.com
> Subject: COZY: headrests
> Date: Saturday, October 02, 1999 8:51 PM
> 
> Builders,
> 
> I'm making the headrests today, and it occurred to me that it would be
> easier to leave the back off the right one until I get the wiring of the
> headset jacks done (the right headrest seems as good a place to put the
> jacks as any).  Is there any reason not to do that?  Has anyone else done
> this?
> 
> Doug Shepherd
> 

From: cdenk@ix.netcom.com
Date: Sat, 2 Oct 1999 21:45:00 -0500 (CDT)
Subject: Re: COZY: headrests

My Bose interfaces and headphone jacks are on the horizontal surface between the headsets. Then the cables are behind your 
elbows and not in the way. The centerline facing headrest sides have slots in them for storage. Usually the flight guides are 
there, readily available, but out of the way. The ELT antenna is bracketed to the aft of the front  seat back, with the whip 
antenna sticking up unto the pilots headrest.

From: "DougSheph" <dougsheph@home.com>
Subject: Re: COZY: headrests
Date: Sat, 2 Oct 1999 20:53:56 -0700

Carl, you said

>The ELT antenna is bracketed to the aft of the front  seat back, with the
whip
> antenna sticking up unto the pilots headrest.

You have the front-hinged canopy, right?  Are both headrests fixed to the
front seatback in that configuration?  I could consider that on the right
headrest, but not the left one.

The more I look at all that empty space in the right headrest, the more I
think I should make use of it somehow.  How about a flashing beacon light
power supply?  I need to have one somewhere, and that would get it out of
the way, although it would require re-opening the headrest if it ever needs
service.  Does anybody know how often one of those needs servicing or
replacing (I've never owned a plane)?  Do they dissipate a lot of heat, too
much to put it in an enclosed space?

Doug Shepherd

From: cdenk@ix.netcom.com
Date: Sun, 3 Oct 1999 07:43:51 -0500 (CDT)
Subject: Re: COZY: headrests

On 10/02/99 20:53:56 you wrote:
>
>Carl, you said
>
>>The ELT antenna is bracketed to the aft of the front  seat back, with the whip antenna sticking up unto the pilots headrest.
>
>You have the front-hinged canopy, right?  Yes
 Are both headrests fixed to the front seatback in that configuration?  Yes

How about a flashing beacon light power supply? My strobe power supply is on the forward face of the firewall, within inches 
of the battery and master relay. To eliminate noise in the headsets, I had to install a relay to keep wiring very short, a 
filter capacitor, and then found the dress (location) of the short wires was very critical (trial and error). By mounting in 
the headrest, all those wires get much longer and would increase the chances of noise in the headsets. 

(strobe power supply) how often one of those needs servicing  Yes in particular if out of service for some time, but they do 
go bad, there are some health sized capacitors inside. A few years back Terry Schubert had to pull a wing to replace his power 
supply, its mounted on the end of the strake.
>


Date: Sun, 03 Oct 1999 09:17:18 -0400
From: Jeff Russell <JRaero@gte.net>
Subject: Re: COZY: headrests

DougSheph wrote:

> Is there any reason not to do that?  Has anyone else done
> this?

I did this on my Cozy 3 and AeroCanard.  Works great.

-- 
Jeff

From: Militch@aol.com
Date: Thu, 21 Oct 1999 21:34:47 EDT
Subject: COZY: Headrests

I didn't see this question in the archives, so I must be getting really dull 
if I am the first person who couldn't figure it out

When Chapt 8, page 1 says to put 1 layer of BID on the foam parts for the 
headrests, will that layer of glass go on the inside of the finished 
headrests (my interpretation since page 2 talks about glassing the outside) 
or the outside.  I can't see how the headrests can be strong enough for their 
purpose unless there is glass on both sides, so the inside is the logical 
choice.  Of course, the plans might have meant - glass both sides with one 
ply of bid, then cut up and glue together, but they don't specifically say 
"both sides" and generally they are specific.

Thanks,
  Peter Militch Cozy Mk IV Chapt 7/8

From: cdenk@ix.netcom.com
Date: Thu, 21 Oct 1999 23:25:08 -0400 (EDT)
Subject: Re: COZY: Headrests

My headrests are glassed inside, and there are slots on the faces facing the airframe centerline to store Flight Guide, etc.

From: Wayne Hicks <whicks@zeltech.com>
Subject: RE: COZY: Headrests
Date: Fri, 22 Oct 1999 09:47:31 -0400



-----Original Message-----
From: Militch@aol.com [mailto:Militch@aol.com]
Sent: Thursday, October 21, 1999 9:35 PM
To: cozy_builders@canard.com
Subject: COZY: Headrests

Peter Militch asks:
I didn't see this question in the archives, so <snip> when Chapt 8, page 1
says to put 1 layer of BID on the foam parts for the 
headrests, will that layer of glass go on the inside <snip> or the outside?

Wayne Hicks responds:  
I'd interpret as 1-BID glass on the inside only, cut out the pieces, the
glass the outside with 2-BID and tape as in Step 4.  The clue is that Step 4
says to round the edges, vacuum, and micro the foam before glassing the
2-BID.  Can't do that if it's already glassed, right?

-------> Let me know what Nat says to do.  Then I can get with bil kleb to
update you Q&A into the Chapter 8 FAQ's.

___________________________________
Wayne Hicks
Cozy IV #678
Chapter 18
http://www.geocities.com/yosemite/falls/2027

From: Militch@aol.com
Date: Fri, 22 Oct 1999 13:12:04 EDT
Subject: Re:  RE: COZY: Headrests


In a message dated 10/22/99 1:52:22 PM, whicks@zeltech.com wrote:

>-------> Let me know what Nat says to do.  Then I can get with bil kleb to
>
>update you Q&A into the Chapter 8 FAQ's.
>

Thanks Wayne, Nat says you got it right. This is what I planned to do anyway, 
but it's nice to get confirmation.

Regards

From: mikefly@juno.com
Date: Fri, 22 Oct 1999 14:06:50 -0500
Subject: Re: COZY: Headrests



On Thu, 21 Oct 1999 21:34:47 EDT Militch@aol.com writes:
>When Chapt 8, page 1 says to put 1 layer of BID on the foam parts for 
>the 
>headrests, will that layer of glass go on the inside of the finished 
>headrests (my interpretation since page 2 talks about glassing the 
>outside) 
>or the outside. 

Peter,
On the Long EZ, the head rest pieces are cut to size and glassed on the
inside with one ply. After partial cure, the pieces are assembled on the
seat back with micro and small nails. After cure, remove nails, sand to
shape and cover with two plies BID.
P.S. 
The top of the head rest is a good place to mount a GPS antenna. Mine was
an after thought and was easily changed, but doing it now will save time
later.

Mike Bowden 

From: "Doug Shepherd" <DougSheph@home.com>
Subject: COZY: shoulder support nutplates
Date: Sat, 20 Nov 1999 20:13:38 -0800

I installed the shoulder support nutplates as follows:  I flox'ed the birch
inserts in place, then installed the pads to bring them flush on the top
side of the foam.  Then I drilled the 1/4" hole, put some Vaseline on the
bolts, put some flox under the nutplates, and screwed them together with
some washers under the bolts.  Before removing the bolts, I Dremel'ed the
mounting holes on the nutplates clear, then drilled holes and installed #2 x
1/4" screws.  The #2 screws don't have much strength but they do pin the
nutplates, preventing them from torquing when the bolts are installed.  Then
I put some scotch tape on the outside, dripped some candle wax into the
hole, removed the tape, then installed the shoulder support and glassed over
the outside.  Then I just had to drill through the outer two layers of
fiberglass and knock out the wax plug.

It seemed to work pretty well.  All the holes line up, the threads are
clean, and the nutplates take plenty of torque without any cracking or other
scary noises.

Doug Shepherd

